Lawn Tractor Rear Tire Chains

Saturday, April 14, 2012

Winter RV Battery Storage

Winter RV Battery Storage


The two most common causes for RV battery failure are undercharging and overcharging.

Winter RV Battery Storage

Winter RV Battery Storage

Winter RV Battery Storage


Winter RV Battery Storage



Winter RV Battery Storage

Undercharging is a result of batteries being repeatedly discharged and not fully recharged between cycles. If a battery is not recharged the sulfate material that Fasteners to the discharged portions of the plates begins to harden into crystals. Over time this sulfate cannot be converted back into active plate material and the battery is ruined. This also occurs when a battery remains discharged for an extended period of time, like during storage. Sulfation is the number one cause of battery failure. The second leading cause of battery failure is overcharging. Overcharging batteries results in severe water loss and plate corrosion. With thatsaid let's look at how to properly store your RV batteries.

Before we talk about storing the batteries we need to talk about battery safety. Lead acid batteries contain sulfuric acid which is extremely corrosive and can cause severe burns or even blindness. And the hydrogen gas that batteries produce when they're charging is very explosive. When you work around batteries you need to wear goggles and gloves, remove all jewelry and do not smoke or use any open flames.

Caution: If you accidentally get battery acid on your skin, flush it with lots of water and if it gets in your eyes flush with low pressure water for 15 minutes and call a doctor.

When you put the RV in long term storage it's a good idea to remove the batteries and put them in storagetoo. This is quite simple to do. The first thing we want to do is visually inspect the batteries for any obvious damage. Any fluid on or around the battery may be an indication that electrolyte is leaking from the battery. A damaged or leaking battery should be replaced immediately. Whenever you remove any battery always remember to remove the negative terminal or cable first, and then the positive cable.

Battery Tip: When you remove a battery turn off the ignition switch, all electrical switches, and any battery disconnect switches before you disconnect the battery cables. Whenever you remove any battery cables label them first so you remember how they go back on the battery. When you reinstallthe battery do it in the reverse order. Install the positive cable first and then the negative cable.

Clean the batteries with a 50-50 mixture of baking soda and water if necessary, i.e. use one pound of baking soda to one gallon of water. Now you can check the electrolyte level in each cell and add distilled water if necessary. The minimum level required is at the top of the plates. If it's below the plates add enough distilled water to cover the plates before you charge the battery.

Test the battery state of charge with a voltMeter or flyoverpasific and charge any batteries that are at or below 80%. An 80% charge is approximately 12.5 volts for a 12 volt battery and 6.25 volts for a 6 volt battery. Lead sulfation starts when abattery state of charge > drops below 80%. After charging the batteries check and fill each cell to 1/8 inch below the fill well with distilled water. Overfilling cells will cause battery acid to overflow.

Caution: Batteries should only be charged in a well ventilated area and keep any sparks and open flames away from a battery being charged. Check the electrolyte levels before and after charging batteries.

A discharged or partially charged battery will freeze much Faster than a charged battery. Store the batteries in a cool dry place but not where they could freeze. Batteries in storage will loose a percenTAGe of current through internal leakage. It's not uncommon for a battery to discharge up to 10% a month when it is beingstored. Cold temperatures slow this natural discharge process down and warmer temperatures speed the process up. Test the
the stored battery state of charge every month and charge batteries that are at or below an 80% state of charge.

Completely charge the batteries before re-installing them next spring. For optimum performance you can equalize the batteries after they are fully charged. An equalizing charge is an increase in charging volTAGe similar to a charge to convert any bulk crystallized lead sulfate back into its original components.

If you decide to leave the batteries in the RV while it is in storage remember to check the state of charge monthly and charge any batteries at or below an 80% charge. Some RV converter multi-sTAGe chargers and aftermarketchargers are designed to maintain a float charge on the battery without removing the batteries from the RV. Remember, for the converter charger to work the RV will need to be Plugged in to electricity.

For more information on RV batteries check out our Deep Cycle Battery Care & Maintenance DVD.

Happy Camping,

Mark Polk

Copyright 2007 by Mark j. Polk, owner of RV Education 101

Winter RV Battery Storage

Monday, March 12, 2012

Choosing the Right Tractor Tire Chains

Choosing the Right Tractor Tire Chains


Tractor Tire chains like in many of the same models, styles, and designs as other Tire chains. Depending on the size and brand of the tractor and tractor wheel, a variety of Tire chains can be found.

Choosing the Right Tractor Tire Chains

Choosing the Right Tractor Tire Chains

Choosing the Right Tractor Tire Chains


Choosing the Right Tractor Tire Chains



Choosing the Right Tractor Tire Chains

Like most other types of Tire chains, there are many different options available in tractor tire chains. The most popular choice, and the most widely recomMended, is two-link spacing with an optional V-Bar. Two link spacing means that there is a cross chain every second side chain link. Basically, it has twice as many cross chains as the four-link spacing, which only has a cross chain every fourth side chain link. The extra> chains provide for a more steady, smooth ride and more steering control. The optional V-Bar chains are extremely helpful on ice, hills, and other hard-packed conditions. While V-Bar chains are available in both two-and four-link spacing, they should not be used on paveMent since they can damage the surface of the road.

Kubota Tractor tire chains are available in the basic two-and four-link chains. Kubota recomMends using tire chains and wheel Weights in icy conditions. Even when using tire chains, drivers should still drive at a speed slow enough to maintain complete control of the tractor at all times.

Choosing the Right Tractor Tire Chains

Tuesday, February 7, 2012

Difference Between a Conventional and a Maintenance-Free Motorcycle Battery

Difference Between a Conventional and a Maintenance-Free Motorcycle Battery


Most modern motorcycles require a motorcycle battery to power its electrical systems. Currently, there are two main types available in the market: the conventional type and the maintenance-free type. Although they are an often overlooked component, knowing the differences between the two types of batteries can help one better understand their specific maintenance needs and cost.

Difference Between a Conventional and a Maintenance-Free Motorcycle Battery

Difference Between a Conventional and a Maintenance-Free Motorcycle Battery

Difference Between a Conventional and a Maintenance-Free Motorcycle Battery


Difference Between a Conventional and a Maintenance-Free Motorcycle Battery



Difference Between a Conventional and a Maintenance-Free Motorcycle Battery

The conventional type of battery consists of flooded electrolyte and cell accessible construction. Although these are less expensive than maintenance-free batteries, they require more attention. Because of the process of electrolysis and evaporation, water loss is normal and therefore, the periodic addition of distilled water is required. If the battery's water level fallsbelow the minimum fill line, permanent damage to the battery can occur as the lead plates become exposed to the Air. For this reason, it's important to maintain the water levels above the minimum fill lines.

With a maintenance-free battery, on the other hand, water loss is eliminated since the unit is designed to remain permanently sealed once it is filled with acid. Although slightly more expensive than conventional batteries, it is currently popular among many motorcycle enthusiasts. Because the battery unit is completely sealed, all of the acid is absorbed in the special plates and separators-there is no need to worry about acid leaks, or refilling the battery with distilled water. Even after months of normal use, there would be enoughelectrolytes 15 to keep the plates covered because of the amount of free-standing electrolytes 15 that are above the plates.

Knowing the difference between the two types of batteries can help to make a better rider decision as to what type of motorcycle battery to use for his bike and maintenance habits. Either way, properly maintaining battery will help ensure its long-term use, and can save money in the long run.

Difference Between a Conventional and a Maintenance-Free Motorcycle Battery

Thursday, January 5, 2012

Pulling Wooden Fence Posts

Pulling Wooden Fence Posts


Wooden fence posts in the Raleigh NC area are usually set 24" in the ground and have a 60-80 pound concrete footer holding them in place. When the posts were set, there was surely the intention that the fence they supported would be around for many years. Now you have decided that the old fencing needs to be removed. Getting the pickets off and the runners down was an easy task, but now you have wooden fence posts that are securely set in the ground and seem to be content on staying there.  You ask yourself if there is an easier way to get the fence posts out that doesn't require you to dig out every footing.

The answer is yes, there is an easier way! All you need is a drill, a 2 1/2" paddle bit, a 4' piece of deck board, and a bumper jack. A bumper jack, also known as a farm jack, is a jack that was used many years ago to jack up cars to change Tires. The jack was designed to go under the bumper and lift the vehicle. Back in the day, bumpers were made of steel and could take the weight of the vehicle. Of course with present day cars, this would most likely tear the bumper off your car. But bumper jacks are still available in most tractor Supply and agricultural stores. Bumper jacks can lift up to 5000 lbs. Farm jacks, which look the exact same as a bumper jack, can lift 7000 lbs or more. Both jacks cost around .00.

The technique described is for removing wooden fence posts that will be discarded. In other words, the posts will not be able to be reused. Put the 2 1/2" paddle bit in your drill. Drill a hole half way through the fence posts about 1 foot from the ground. Try not to go all the way through the post. The idea is to make a hole big enough to get the lifting mechanism of the jack into. If you go all the way through the post, the post may break before coming out of the ground. Place the deck board on the ground in front of the post. The deck board helps transfer the stress and weight while pulling the post out so the jack doesn't start going into the ground instead of lifting out the post. Place the bumper jack on the deck board and place the lifting mechanism in the hole you made. Start pumping the jack and you will see the post to start lifting out of the ground. If the top of the jack wants to start going forward, place the included guard on the face of the post. Keep working the jack until the post is out of the ground. You may have to manually pull the post the last couple of inches. 

This is a Fast, easy, and inexpensive way to remove wooden fence posts. Just be careful not to get pinched between the top of the jack and the post! 

Pulling Wooden Fence Posts


Pulling Wooden Fence Posts


Pulling Wooden Fence Posts



Friday, December 2, 2011

A Look at Automatic Tire Chains

A Look at Automatic Tire Chains


With technology always advancing, it is no wonder that automatic Tire chains have made their way into the Tire chain market. These tire chains take away the pain of attaching tire chains in wintry or wet conditions, and can save drivers a lot of time.

Automatic tire chains can be used on pickup trucks, RVs, mobile homes, trucks, and buses, and they offer the traction of a single set of conventional Snow chains at the touch of the button, which means an end to stopping and getting out of the vehicle.

To install automatic tire chains, drivers mount an electric switch to their dashboard, which provides 12 volts to an Air solenoid mounted on the vehicle's frame rail. Compressed Air is then supplied from either the vehicle's onboard Air system or a 12-volt compressor kit. When the dashboard switch is activated, the solenoid opens, thus allowing compressed Air to enter the air cylinder and lower the chain wheel so that it contacts the inside of the tire. The friction between the tire and the rubber-covered chain wheel then causes the chain wheel to rotate, which creates enough centrifugal force to wave the chains out in front of the tire. Chain is spaced at 60-degree intervals in sixth lengths on the chain wheel. This guarantees that there are always two chains between the tire and the road service, regardless of whether the driver is accelerating or decelerating. The traction is obtained both in forward and reverse. When the dashboard switch is turned off, the solenoid exhausts the air, and the chain wheels are brought back to their resting position.

Automatic tire chains are a great new technology for anyone who wants tire chains -- but does not want the inconvenience of getting out of their car and installing the chains in adverse weather conditions.


garden tractor tire chains